Study of tribological properties of polymer derived ZrB2-SiC ceramics

ZrB₂–SiC composite ceramics with different compositions (20 and 60?vol% ZrB₂–SiC, 20ZS and 60 ZS, respectively) were prepared. Wear tests were conducted on the obtained ceramics in multiple distances using ball-on-flat tribotester. Volume loss and cross-sectional profiles of samples were measured by three–dimensional (3D) profilometer to study the onset of track wear damages. Pressure–depth curves and hardness were measured by indentation to investigate defects produced in the tribo-film by the debris. The debris of 20ZS was found to be joined to the tribo-film and accumulated with distance, shifting from microcrack (＜10,000 cycles) to abrasive wear (50,000 cycles). Compared to 20ZS, lower debris accumulation of 60ZS resulted in better wear resistance, leading to thinner and more stable non-substrate regions for this sample. These differences between both samples basically resulted from different particle sizes. Fine grains were easily pulled out in the experiment, resulting in abrasive wear of the specimen. While transgranular fracture of grains and the pinning led to larger grains with less debris, the damage mode remained transgranular fracture.     

Moderate lameness leads to marked behavioral changes in dairy cows

Lameness is one of the most prevalent diseases affecting the welfare of cows in modern dairy production. Lameness leads to behavioral changes in severely lame cows, which have been investigated in much detail. For early detection of lameness, knowledge of the effects of moderate lameness on cow behavior is crucial. Therefore, the behavior of nonlame and moderately lame cows was compared on 17 Swiss dairy farms. On each farm, 5 to 11 nonlame (locomotion score 1 of 5) and 2 to 7 moderately lame (locomotion score 3 of 5) cows were selected for data collection in two 48-h periods (A, B) separated by an interval of 6 to 10 wk. Based on visual locomotion scoring, 142 nonlame and 66 moderately lame cows were examined in period A and 128 nonlame and 53 moderately lame cows in period B. Between these 2 periods, the cows underwent corrective hoof trimming. Lying behavior, locomotor activity, and neck activity were recorded by accelerometers (MSR145 data logger, MSR Electronics GmbH, Seuzach, Switzerland), and feeding and rumination behaviors by noseband sensors (RumiWatch halter, ITIN + HOCH GmbH, Liestal, Switzerland). Furthermore, visits to the brush and the concentrate feeder, and the milking order position were recorded. In comparison with nonlame cows, moderately lame cows had a longer lying duration, a longer average lying bout duration, and a greater lateral asymmetry in lying duration. Average locomotor activity, locomotor activity during 1 h after feed delivery or push-ups, and average neck activity were lower in moderately lame cows. Eating time and the number of eating chews (jaw movements) were reduced in moderately lame compared with nonlame cows, whereas no effect of moderate lameness was evident for ruminating time, number of ruminating chews and boluses, and average number of ruminating chews per bolus. Moderately lame cows visited the concentrate feeder and the brush less frequently, and they were further back in the milking order compared with nonlame cows. In conclusion, nonlame and moderately lame cows differed in a biologically relevant way in many of the behavioral variables investigated in this study. Therefore, the use of these behavioral changes seems to be promising to develop a tool for early lameness detection.     

New anti-ablation candidate for carbon/carbon composites: Preparation,composition and ablation behavior of Y2Hf2O7 coating under an oxyacetylene torch

Y₂Hf₂O₇ possesses low thermal conductivity and high melting point, which make it promising for a new anti-ablation material. For evaluating the thermal stability and the potential applications of Y₂Hf₂O₇ on anti-ablation protection of C/C composites, Y₂Hf₂O₇ ceramic powder was synthesized by solution combustion method and Y₂Hf₂O₇ coating was prepared on the surface of SiC coated C/C composites using SAPS. Results shown that the coating exhibits good ablation resistance under the heat flux of 2.4?MW/m² with the linear and mass ablation rates are 0.16?μm?s^?1 and ?0.028?mg?s^?1, respectively, after ablation for 40?s. With the prolonging of the ablation time, the increasing thermal stress causes the increase of cracks. Moreover, the chemical erosion from SiO₂ and the physical volatilization of low temperature molten products aggravate failure of the Y₂Hf₂O₇ coating.     

Effect of texture on oxidation resistance of Ti3AlC2

Oxidation resistance of textured Ti₃AlC₂ ceramics was measured in the temperature range 1273–1573?K. It was found that the oxidation was markedly anisotropic and the samples exhibited a better oxidation resistance when tested along a direction transverse to the c-axis. This behavior was attributed to the rapid diffusion of Al within its basal planes to form a passivating Al₂O₃ scale and it respected Ellingham diagrams. The scales formed had different compositions depending on the testing direction; this response was clearly resulting from the crystallographic orientation. Even at 1473?K after 20?h exposure, the samples tested in a direction transverse to the c-axis showed a reduced weight gain which was 45 times lower than one seen on a basal plane.     

Protective nature of nano-TiN coatings shaped by EPD on Ti substrates

The hardness and corrosion resistance of TiN coatings, processed by Electrophoretic Deposition (EPD) to cover polished and unpolished Ti substrates, have been evaluated. A deposition time of 5 min has been enough to obtain a cohesive layer of 7–8 μm in thickness. The coatings were thermally treated in vacuum atmosphere at 1200 °C for 1 h with heating and cooling rates of 5 °C min^?1. The surfaces have been covered homogeneously optimizing the properties of the Ti substrates. Uniform and dense TiN coatings have been obtained onto polished substrates, while on unpolished Ti the nitrogen diffuses toward the substrate, moderately dissolving TiN coating. The nanohardness values of the polished samples have been increased from 2.8–4.8 GPa up to 6.5–8.5 GPa. Besides, the corrosion current density has been reduced more than one order of magnitude obtaining a protective efficiency of 82%. These values have been compared with other works in literature where authors used complex and costly processing techniques, demonstrating the strong impact of the colloidal processing over the specific properties of the material.     

Influence of whisker-aspect-ratio on densification,microstructure and mechanical properties of Al2O3 whiskers-reinforced CeO2-stabilized ZrO2 composites

A novel composite of 12 mol% CeO₂-stablized tetragonal ZrO₂ reinforced with Al₂O₃ whiskers (designated as Ce-TZP/A_w) has been prepared and studied in this work. The objective of this investigation was to systematically study the influence of whisker-aspect-ratio on the densification behaviors, microstructure evolution, and mechanical properties of Ce-TZP/A_w composite. Results showed that the sintered density of composite increased and the grain growth tended to diminish with the decrease in whisker aspect radio. Both the fracture toughness and flexural strength reached maximum values of 475 ± 12 MPa and 11.4 ± 0.2 MPa m^1/2, respectively at a whisker aspect ratio of about 12. It was also observed that the fracture toughness, flexural strength and tetragonal to monoclinic ZrO₂ transformation of the dual-phase composite exhibited similar variation trend as a function of the whisker-aspect-ratio, which suggested that the stress-induced phase transformation should be the main toughening and strengthening mechanism in the Ce-TZP/A_w composite.     

Anionic Redox Chemistry as a Clue for Understanding the Structural Behavior in Layered Cathode Materials

The anionic redox chemistries of layered cathode materials have been in focus recently due to an intriguing phenomenon that cannot be described by the number of electrons of transition metal ions. However, even though several studies have investigated the anionic redox chemistry of layered materials in terms of the charge compensation, the relationship between the origin of the structural behavior and anionic redox chemistry in layered materials remains poorly understood. In addition, a simultaneous redox process of transition metal ions could occur through the d bands interaction. Here, it is demonstrated that the anionic redox chemistry is associated with the anisotropic structural behavior of the layered cathode materials albeit without providing additional capacities exceeding the theoretical values. These findings will provide a foundation of a new chapter in the understanding of the properties of materials.     

Multi-objective optimization for efficient modeling and improvement of the high temperature PEM fuel cell based Micro-CHP system

Fuel cells due to different useful features such as high efficiency, low pollution, noiselessness, lack of moving parts, variety of fuels used and wide range of capacity of these sources can be the main reasons for their tendency to use them in different applications. In this study, the application of a high temperature proton exchange membrane fuel cell (HT-PEMFC) in a combined heat and power (CHP) plant has been analyzed. This study presents a multi-objective optimization method to provide an optimal design parameters for the HT-PEMFC based micro-CHP during a 14,000 h lifetime by considering the effect of degradation. The purpose is to optimize the net electrical efficiency and the electrical power generation. For the optimization process, different design parameters including auxiliary to process fuel ratio, anodic stoichiometric ratio, steam to carbon ratio, and fuel partialization level have been employed. For optimization, A new technique based on Tent mapping and Lévy flight mechanism, called improved collective animal behavior (ICAB) algorithm has been employed to solve the algorithm premature convergence shortcoming. Experimental results of the proposed method has been applied to the data of a practical plant (Sidera30) for analyzing the efficiency of the proposed ICAB based system, it is compared with normal condition and another genetic algorithm based method for this purpose. Final results showed that the difference between the maximum electrical power production under normal condition and ICAB based condition changes from 2.5 kW when it starts and reaches to its maximum value, 3.0 kW, after 14,000 h lifetime. It is also concluded that the cumulative average for the normal and the ICAB based algorithm are 24.01 kW and 27.04 kW, respectively which showed about 3.03 kW cumulative differences.     

Using contingent behavior analysis to measure benefits from rural electrification in developing countries: an example from Rwanda

Hundreds of millions of people in Sub-Saharan Africa do not have access to electricity and will not receive it from national grids in the next few decades. Electricity makes up an important component of rural development and so increasing access can have positive socioeconomic benefits. In this study, we use contingent behavior analysis to quantify the potential benefits of electricity in rural Rwandan villages which currently do not have electricity. The proposed method allows for calculation of net benefits as well as electricity bills. We find that even relatively poor, isolated households would pay for electricity, though amounts vary across households and this affects the financial viability of electrification. Common uses for electricity include lighting, battery charging, and agricultural processing. Despite heterogeneity, opportunities exist to improve rural economic welfare through increased electricity access.